Fields of application
Transparent finish of interior floor coverings, mechanical-resistant impregnations, anti-dust and anti-oil for concrete surfaces.
Allowed supports
Concrete
Prefabricated concrete
Tiles
Floor screed
Rock walls
Preparation of supports
The media should have adequate mechanical resistance. The concrete surfaces should be cured, dry, planar and absorbent, free from oils, detergents, powders and soiling. The most appropriate type of mechanical preparation should also be determined (degreasing or shot peening).
Conveniently absorbent surfaces may be dealt with directly after a proper cleaning. For tiled surfaces and for pre-existing coverings in resin, a degreasing or shot peening treatment is required until complete opacification and complete elimination of dust.
Mode of use
Mix components A and B each in their own container before mixing. Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Pour component B into a suitable container and add component A. Mix everything for a few minutes using a mechanical stirrer with variable speed until a homogeneous and uniform color mixture is obtained. Leave to rest for a few minutes and mix again. Dilute the final product only with water in the Syntech Pavisheer: water ratio of 1: 3 for the first coat and 1: 2 for the second. Gradually add the dilution water, continuing to mix for a few minutes. The dilution ratio can vary according to the porosity of the support; if necessary on closed surfaces it is also possible to dilute the second coat respecting the dilution ratio 1: 3. The Syntech Pavisheer emulsion has a stability of about 2 hours at 20 ° C; within this period the product must be used. Syntech Pavisheer is applied with a short-haired roller or spray, covering the entire surface evenly. We recommend application at temperatures not lower than 5 ° C.
Technical specifications
Viscosity
FORD ASTM D 1200
15 ± 2 s
Adhesion by direct traction
EN 1542
> 1 N/mm²
Complete hardening at 20°C
a 20°C
7 day
Touch hardening at 20°C
a 20°C
12 h
Time before second coat at 20°C
4-24 h
Consumption
From 0.10 to 0.15 kg of SYNTYECH PAVISHEER for each square metre of surface to be covered.
Packaging and dimensions
Can 5 kg [A]
Can 5 kg [B]
Canister 1 kg [A]
Canister 1 kg [B]
Kit: 1 Canister 1 kg [A] + 1 Canister 1 kg [B]
Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B]
Storage and conservation
Protect from freezing.
Warnings
The general information, along with any instructions and recommendations for use of this product, including in this data sheet and eventually provided verbally or in writing, correspond to the present state of our scientific and practical knowledge.
Any technical and performance data reported is the result of laboratory tests conducted in a controlled environment and thus may be subject to modification in relation to the actual conditions of implementation.
Azichem Srl does not assume any liability arising from inadequate characteristics related to improper use of the product or connected to defects arising from factors or elements unrelated to the quality of the product, including improper storage.
Those wishing to utilise the product are required to determine prior to use whether or not the same is suitable for the intended use, assuming all consequent responsibility.
The technical and characteristic details contained in this data sheet shall be updated periodically. For consultation in real time, please visit the website: www.azichem.com. The date of revision is indicated in the space to the side. The current edition cancels out and replaces any previous version.
Please note that the user is required to read the latest Safety Data Sheet for this product, containing chemical-physical and toxicological data, risk phrases and other information regarding the safe transport, use and disposal of the product and its packaging. For consultation, please visit: www.azichem.com.
It is forbidden to dispose of the product and/or packaging in the environment.
